We’re at NCSEA in San Francisco, Oct 28–29 · Booth 110NCSEA · Booth 110 · Oct 28–29

Guide · Specifications and drawings · 23 21 23

Check hydronic pump specifications against the pump schedule, flow diagram, mechanical room plans, and electrical and controls drawings

UFGS Section 23 21 23 Hydronic Pumps, a USACE-prepared guide specification revised in May 2025, covers pumps primarily for chilled water, hot water, and condenser water service in building HVAC systems: wet rotor and three-piece circulators, small and large in-line pumps, base-mounted end suction pumps (flexible or close coupled), double suction split case pumps, vertical lineshaft turbine pumps, and cooling coil condensate pump units. It specifies selection and pump curves, materials, seals, couplings, motors, variable speed by adjustable speed drive, combination motor and drive, or electronically commutated motor, an optional packaged pump system with its own controller, guards and suction diffusers, installation and alignment, and field tests. It superseded UFGS 43 21 13 and 43 21 39 when first issued in August 2017.

Start with the opening drawing note of the issued Section 23 21 23: the drawings must show each pump’s minimum design flow and pressure, motor voltage, phase, and power, speed, maximum Pump Efficiency Index, minimum efficiency, vibration isolation, any variable frequency drive or EC motor, and a pump type that matches the section’s own terms. Then check the pump schedule against the type paragraphs kept, the system curve where pumps run in parallel, the mechanical room for pads, supports, and service access, and the electrical and controls drawings for drives, starters, and interfaces.

Assemble the review package

Gather the hydronic flow diagrams, the pump schedule and any system head curves, the mechanical room plans and sections, the pump installation, pad, inertia base, and support details, the vibration isolation schedule, the electrical plans and motor or equipment connection schedule, the VFD schedule, the controls drawings, points list, and sequences, and the issued Section 23 21 23 with Sections 23 05 15, 26 20 00, 26 29 23, 23 09 00 or the DDC section the project uses, 23 05 93, and 03 30 00. Follow one pump from its schedule row to its pad, its motor circuit, and its control point before assuming the others match.

WBDG publishes UFGS 23 21 23: Hydronic Pumps as a public guide-specification reference (accessed November 18, 2026). Use your project’s issued specification and amendments for the actual comparison; the guide specification does not automatically govern your project. The checklist below is an original suggested review workflow, not a reproduction of the UFGS requirements.

Eight checks to run against the issued set

Use one record per location or system. The CSV contains the same eight prompts plus fields for source revisions, observed evidence, the review owner, the decision, and closure references.

Eight specification-to-drawing checksSwipe or scroll sideways to read all columns.
CheckSources to compareQuestion to resolve
The pump schedule and the drawing noteOpening drawing note (minimum design flow and pressure; motor voltage, phase, and power; speed; maximum PEI; minimum efficiency; vibration isolation; VFD or EC motor; pump type matched to the section’s terminology) + Hydronic Pumps note (correlate the schedule with the type names) + note on pumps specified in other sections + pump schedule and flow diagramDoes every pump on the flow diagram appear in the schedule with each item the note lists, does each type use the section’s names (circulator, small or large in-line, end suction, double suction, vertical lineshaft turbine, condensate pump unit), and is it clear which pumps come packaged with chillers, boilers, or other equipment under their own sections?
Duty point, curves, and parallel operationPump Characteristic (pumps must discharge at heads “between the following limits:” with no limits following; brackets for matching the system head curve, suction lift, and shutoff head; Preferred Operating Region per HI ANSI/HI 9.6.3) + Selection Criteria (selection near maximum efficiency; impellers within published range; PEI under 10 CFR 431) + Equipment Data (curves for each pump and each parallel combination, with the system curve; parallel pumps must cross the system curve alone and together) + schedule and system curveWith the flow and head limits missing from the paragraph, does the schedule give the duty point for every pump, is a system head curve shown wherever the parallel or series bracket is kept, and will the submitted curves show each pump alone and in parallel against that curve?
Pump types, materials, and fluid temperatureType paragraphs (working pressure and flange class brackets; impeller, casing, and shaft material notes that limit bronze, cast iron, and carbon steel above a stated temperature; seal flushing heat exchanger note) + Circulator (wet rotor or three-piece; NSF 372 lead content for potable service; the Seal Assembly note retaining a mechanical seal for wet rotor potable circulators) + Close Coupled note (discouraged except where floor space is extremely limited) + schedule fluid temperature and pressureDoes the schedule give the fluid temperature and working pressure that the material notes and flange class brackets depend on, is a close coupled pump shown only where the room is that tight, and has the specifier confirmed which circulator type the seal paragraph belongs to?
Mechanical room, pads, and supportsInstallation (access space no less than the manufacturer recommends) + Base Mounted, Long-Coupled Pumps (shims, grouted baseplate; bracketed concrete foundation integral with the floor or separated, with a filler strip “as shown”) + Large Vertical Inline Pumps (supported by hangers on the connected piping, plus stanchion or pipe-stool floor supports on neoprene pads) + Large In-Line note (support when mounted horizontally) + Pump Suction Diffuser bracket + mechanical room plans, sections, and detailsDo the plans show service access around each pump and room to pull a motor or rotating assembly, is a pad or foundation detailed for each base-mounted pump with the filler strip the section expects, are hangers and floor supports for in-line pumps detailed with the added pump weight, and is a suction diffuser or straight inlet shown where inlet conditions need one?
Vibration isolation, couplings, and alignmentOpening drawing note (vibration isolation) + Baseplate (stiffness per HI 1.3; open grouting area) + Coupler and Spacer Coupling (flexible element; guards per 29 CFR 1910.219 and NEMA Z535.4) + alignment (cold checks before and after grouting and after piping, final hot check, tighter limits with VFDs) + Pump Motor/Alignment Report + isolation schedule and detailsDoes the vibration isolation shown for each pump agree with a grouted baseplate on a foundation, are flexible connectors or other isolation shown at the pump connections, and does the schedule tell the contractor which pumps are base-mounted and need the alignment report?
Motors, drives, and electrical connectionsMotor paragraphs by type (enclosure brackets; non-overloading across the curve; premium efficiency) + Electric Motors (service factor bracket that differs from the vertical turbine motor’s own bracket; induction, synchronous, or electronically commutated) + Electrical Work (starters and overloads; control wiring “not indicated” provided under this section; Section 26 20 00) + Variable Speed Control (Section 26 29 23 drive, combination motor and drive, or EC motor; inverter-ready note) + Condensate Pump Units (cord and plug or hard wired) + electrical plans, motor and VFD schedulesDo the motor voltage, phase, and power on the pump schedule match the electrical schedule, does each variable speed pump have one drive approach shown on both the mechanical and electrical drawings, is the condensate pump connection the same on both, and has the specifier kept one service factor for each motor?
Controls and packaged pump systemsControl Equipment (start-stop or hand-off-auto; low-water cutoff in the well or on the suction pipe at “the level shown”) + Combination Motor and Adjustable Speed Drive (integration with Section 23 09 00, 23 09 23.01, 23 09 23.02, or the existing system) + Packaged Pump System note (own controller separate from the DDC contractor) + Packaged pumps, piping, base, electrical (main service disconnect, drives, controller, transformer) + Controller, Integration I/O list (primary and secondary pump commands, status, speed, flow), Sequence + controls drawings, points list, sequencesDoes the controls drawing list the points the section exchanges with the DDC system, does the sequence agree with the packaged controller’s role, is the packaged system’s single power feed shown on the electrical plans, and is the low-water cutoff level actually shown where that bracket is kept?
Vertical turbine pumps, tests, and closeoutVertical Lineshaft Turbine (bowls, lineshaft, column pipe, basket strainer; Stuffing Box recommended by its note and Mechanical Seal both unbracketed; Discharge Head calling ASTM A48 Class 30 “high grade ductile iron” though References title A48 gray iron) + Factory Tests (testing per HI 1.3, an applications standard; note citing ANSI/HI 1.6, not in References; Selection Criteria relying on HI 14.6) + Field Quality Control (running test at rated capacity with measured flow) + framed instructions, O&M, training + Section 23 05 93 + sump or well detailsWhere a vertical turbine pump is kept, does the sump or well detail show the setting depth, column, and strainer, and has the specifier chosen packing or a mechanical seal and one discharge head material? Has the specifier named the factory test standard, and is a way to measure flow shown for the field test and for balancing under Section 23 05 93?

Worked example: a chilled water plant with parallel secondary pumps

Illustrative example: a central plant serving a barracks has two constant speed primary chilled water pumps at the chillers, two variable speed secondary pumps in parallel, two large in-line heating hot water pumps, and condensate pump units at ceiling fan coils. The issued Section 23 21 23 keeps the base-mounted flexible coupled end suction and large in-line paragraphs, adjustable speed drives under Section 26 29 23, the parallel pump bracket, and the cord-and-plug condensate pump option. The pump schedule gives flow and head but no PEI, minimum efficiency, or isolation; no system head curve is shown; the base-mounted pumps sit on spring isolators with no inertia base or grouted baseplate detail; the in-line pumps hang from the piping with no floor support; the electrical plans hard-wire the condensate pumps; and the Pump Characteristic paragraph still ends at “between the following limits:”.

Ask the mechanical engineer to add PEI, minimum efficiency, and isolation columns to the pump schedule, draw the secondary system head curve, detail an inertia base or foundation that takes a grouted baseplate under the isolators, and add floor supports under the in-line pumps. Ask the electrical engineer and the mechanical engineer to agree on hard-wired or cord-and-plug condensate pumps and edit the bracket to match. Ask the specifier to fill or delete the missing flow and head limits, choose one service factor for each motor, and settle the factory test standard before the pump submittal is reviewed.

Avoid a false conflict

Section 23 21 23 covers hydronic pumps for HVAC service, their motors, drives, and controls, and packaged pump systems. Hydronic piping, valves, and specialties follow Sections 23 05 15, 23 21 13.00 20, and 23 64 26, drives follow Section 26 29 23, wiring follows Section 26 20 00, controls follow Section 23 09 00 or the DDC section the project uses, balancing follows Section 23 05 93, foundations follow Section 03 30 00, fire pumps follow Section 21 30 00, and pumps furnished with chillers, boilers, or other equipment follow those sections, while federal efficiency rules, NFPA 70, and the mechanical code the project follows govern their own items, so check those before calling a requirement missing. Some of the section’s own wording needs resolving: the Pump Characteristic paragraph introduces flow and head limits that are not there; vertical turbine pumps keep both packing and a mechanical seal; the discharge head calls a gray iron standard ductile iron; two paragraphs give different default service factors; factory tests cite the pump applications standard; and the circulator seal note may point to the wrong circulator type. Ask the specifier which wording the project intends before treating a difference as a design conflict.

When requirements disagree, follow the project’s document-control and clarification process. Do not assume that drawings always override specifications, or the reverse. Identify the exact sources and request an authorized decision.

Close the issue across the affected documents

Record the location or tag, drawing and specification references, issue dates, observed difference, and the decision needed. Assign an owner and keep the item open until the response identifies the governing requirement. Check the revised drawings and specification references together; a response email alone may leave the issued package inconsistent.

For the overall process, use the guide to drawing and specification conflicts. Mark an inapplicable checklist row with a reason, and distinguish a verified correction from a question that still needs design information.

Where Groundbook fits

Groundbook’s drawing and specification review helps investigate potential disagreements in the documents you supply. Include the relevant specification sections and drawing references, then verify the cited evidence with the responsible reviewers before acting on a finding.

Questions, answered

FAQs

What should a hydronic pump specification review compare?

Compare the pump schedule with the drawing note, the duty points and curves for parallel pumps, pump types and materials against fluid temperature and pressure, the mechanical room pads, supports, and access, vibration isolation and alignment, motors, drives, and electrical connections, controls and packaged systems, and vertical turbine pumps, tests, and closeout.

What drawings does UFGS 23 21 23 expect?

The current UFGS 23 21 23 Hydronic Pumps on WBDG says the project drawings must show the minimum design flow and pressure, motor voltage, phase, and power, pump speed, maximum Pump Efficiency Index, minimum pump efficiency, vibration isolation, any variable frequency drive or EC motor, and the pump type in the section’s terms, and that the pump schedule must correlate with those terms. UFGS numbers are DoD guide specification numbers, not universal MasterFormat titles, and your project’s issued specification governs.

How is this different from the hydronic piping, chilled water piping, and fire pump pages?

UFGS 23 21 13.00 20 and 23 64 26 cover the heating and chilled water piping systems and treat pumps as equipment on the flow diagram, and UFGS 21 30 00 covers fire pumps under NFPA 20. UFGS 23 21 23 covers the HVAC pumps themselves: types, selection, curves, materials, motors, drives, isolation, alignment, and packaged systems. On one project, check that every pump on the flow diagram is assigned to one section and that the pump schedule, piping, and controls drawings describe the same pump.

Can Groundbook check a pump schedule against Section 23 21 23?

Groundbook compares the drawing set with the specification sections and reference documents you upload, such as your issued Section 23 21 23, Sections 23 05 15, 26 29 23, and 23 09 00, the pump schedule, and licensed standards you hold, and returns potential conflicts with links to the source pages. It has no built-in code library and does not select pumps, calculate head or NPSH, size motors or drives, certify compliance, or approve submittals. Each finding is a question for the mechanical engineer of record, the specifier, or the contracting officer.

Bring your next set into focus

Set up a review or talk through your project with our team.

Check your pump schedule against the spec

Trusted by hundreds of professionals