We’re at NCSEA in San Francisco, Oct 28–29 · Booth 110NCSEA · Booth 110 · Oct 28–29

Guide · Structural documents

Engineered wood beam drawing checklist

Engineered wood beams, such as laminated veneer lumber (LVL), parallel strand lumber (PSL) and glued laminated timber (glulam), carry the heaviest loads in most wood-framed buildings. They are also the members most often drawn on one sheet and sized on none.

Check engineered wood beams by confirming that every beam drawn on the supplier layouts, architectural plans and sections is also sized on the structural framing plan, with its product, plies and grade. Then check each beam’s bearing, the post and footing below each end, the hangers where it carries or hangs from other members, the fastening of multi-ply beams, and the product’s suitability for exposed locations.

Find the beams no one sized

Engineered wood beams appear on several documents: the structural framing plan, the truss or joist supplier’s layout, the architectural sections and the ceiling plans. A beam that appears on one of them and not on the structural plan has no engineered size, grade or support.

In the house floor truss submittal load path review, the truss layout called for two long multi-ply LVL beams, one carrying the hung end of a girder and one carrying five trusses. The structural floor plan showed neither. In the same set, a long beam over an open patio carried ceiling joists from both sides with no size label, although every other beam on the sheet had one.

Twelve questions for engineered wood beams

Work through the beams one at a time, starting with those that carry other beams or girders. The CSV has columns for the location, the source references, the reviewer, the status, the decision and the closure evidence. It contains no design values; sizes and capacities come from the engineer of record, the supplier’s design and the manufacturer’s published data.

Engineered wood beam drawing checklistSwipe or scroll sideways to read all columns.
Review areaOpen these sources togetherQuestion to resolve
Every beam on the structural planStructural framing plans, supplier beam and truss layouts, architectural plansIs each beam the supplier layout, architectural plans or sections show also drawn and sized on the structural framing plan?
Size, plies and productBeam callouts, beam schedule, structural notesDoes each callout give depth, width or number of plies, and the product type, with no beam drawn without a size?
Grade or stress classStructural notes, beam schedule, specificationsDo the notes or schedule give one grade or stress class for each engineered wood product, matching the specification?
Multi-ply fasteningBeam details, structural notes, manufacturer requirements citedIs the nailing, screwing or bolting that joins multi-ply beams shown, including side-loaded beams that carry joists or trusses from one side?
Bearing length and supportBeam ends on the framing plan, post schedule, bearing detailsIs the bearing at each beam end shown, with a post, stud pack or wall sized for the reaction?
Posts and footings belowFraming plans, post schedule, foundation planDoes a post or column continue from each beam end to a footing the foundation plan shows?
Beam-to-beam and girder connectionsFraming plans, hanger schedule, connection detailsWhere a beam or girder hangs from another beam, is the hanger or connection named with its capacity and fasteners?
Loads the beam was sized forBeam calculations, structural notes, truss and joist reactionsDo the beam calculations use the same wall, floor and roof loads and the same truss or joist reactions as the drawings?
Exposure and moistureArchitectural plans and sections, beam schedule, specificationsFor beams at porches, patios, decks or other exposed locations, do the drawings state a product and treatment suited to that exposure?
Holes, notches and dropsMechanical and plumbing plans, sections, beam detailsDo any ducts, drains or recessed fixtures pass through or notch a beam, and do the drawings show it as allowed?
Flush and dropped beams in the ceilingsSections, reflected ceiling plans, framing plansDo the sections and ceiling plans show each beam flush or dropped as the framing plan assumes, at the depth drawn?
Who designs which beamGeneral notes, specifications, delegated design and submittal requirementsDo the notes say which beams the engineer of record sizes and which the supplier designs, and who reviews the supplier’s sizing?

Mark a row not applicable only after recording why. A single-span header still needs its bearing and post checked.

Follow each beam end down

An engineered beam concentrates load at its ends. Check that each end has a post, stud pack or wall sized for its reaction, and that the post continues to a footing. The structural load path checklist follows those reactions through every floor. Where one beam hangs from another, the hanger is part of the design: the hanger and connector schedule checklist covers how to check it.

Compare the beams with the specification

The specification may limit the products, grades and treatments allowed. Read the engineered wood and glulam paragraphs of the rough carpentry section against the beam schedule. The rough carpentry specifications versus drawings guide found one federal guide specification requiring laminated strand and veneer products inside its glulam paragraph, which is the kind of conflict to settle before ordering. The AWC NDS guide covers the design standard for the members themselves.

Where Groundbook fits

Groundbook compares the structural framing plans, supplier beam and truss layouts, architectural plans and sections, specifications and calculations you upload, and returns potential conflicts with links to each source, such as a beam on a truss layout that has no size on the structural plan. It does not size beams, check their capacity or choose products. Each finding is a question for the engineer of record and the supplier. See cross-discipline coordination review for the workflow.

Questions, answered

FAQs

Who sizes LVL beams, the engineer or the supplier?

Either can, and the drawings should say which. Often the engineer of record sizes the main beams and the supplier sizes members within its own layout, which the engineer then reviews.

What should an engineered wood beam callout show?

At least the product type, depth, width or number of plies, and grade, consistent with the schedule and notes, plus the bearing and support at each end.

Do multi-ply LVL beams need special fastening?

Yes. The plies must be fastened together as the designer and manufacturer require, especially when the beam carries load from one side. The drawings should show or reference that fastening.

Can engineered wood beams be used outdoors?

Only products and treatments rated for that exposure. Check that beams at porches, patios and decks are specified for the location.

Keep exploring

Continue your review

Structural drawing review checklist

Review structural notes, framing plans, schedules, details, and support interfaces with a practical checklist, worked example, and free editable CSV.

Explore

Structural load path drawing checklist

Follow every load from the roof to the footings across the drawings: girder reactions, posts, transfer walls, hold-downs and supplier members. Free CSV.

Explore

Hanger and connector schedule checklist

Check joist hangers, uplift ties, hold-downs and straps across the framing plans, supplier drawings and specifications. One model per condition. Free CSV.

Explore

Wood truss drawing review checklist

Check wood truss layouts and truss design drawings against the architectural and structural sheets: loads, bearings, headers, uplift and bracing. Free CSV.

Explore

AWC National Design Specification (NDS) for Wood Construction: plan review

Review wood structural drawings against the NDS: design basis, species and grade, members, connections, and engineered products. See checks and limits.

Explore

Check rough carpentry specifications against framing plans, shear wall schedules, and roof nailer details

Compare lumber grades, glulam, sheathing and shear wall panels, treatment, anchors and nailing, bracing, and roof nailers with UFGS 06 10 00.

Explore

Check glued-laminated timber specifications against framing plans, member schedules, connection details, and finish legends

Compare glulam layout, design values and appearance grades, treatment and exposure, connection hardware, finishes, and erection protection with UFGS 06 18 00.

Explore

House floor truss submittal load path

A review of a two-story house’s floor truss package against its structural design finds girder loads, beams and hangers that no engineer’s sheet carries.

Explore

Cross-discipline coordination

Find potential conflicts across architectural, structural, and MEP drawings. Review levels, openings, equipment, and references with linked document evidence.

Explore

Bring your next set into focus

Set up a review or talk through your project with our team.

Find the beams your layouts draw and nobody sized

Trusted by hundreds of professionals