We’re at NCSEA in San Francisco, Oct 28–29 · Booth 110NCSEA · Booth 110 · Oct 28–29

Guide · Specifications and drawings · 03 45 00

Check precast architectural concrete specifications against elevations, finish legends, panel joints, and connection details

UFGS Section 03 45 00 Precast Architectural Concrete, a NAVFAC-prepared guide specification issued in May 2016 and last changed in August 2025, covers plant-cast units whose finish, shape, color, or texture is part of the architecture: wall panels, mullions, sills, copings, railings, bollards, benches, planters, pavers, and similar shapes, conventionally reinforced or prestressed. It sets design to ASCE 7, ACI 318, and PCI MNL-122 with Contractor-designed connections, sealed design and thermal calculations, PCI plant and erector certification by category, facing and backing mixes, aggregates, cementitious materials, embedded inserts, wood nailers, flashing reglets, connection hardware, finishes, a surface finish sample, a full-size sample panel and a mockup, gaskets, thin brick veneer, bearing pads, and insulation, then erection, joints, defect repair, and appearance-based acceptance. Joint sealants follow Section 07 92 00.

Start with the drawing note of the issued Section 03 45 00: confirm that the elevations and details show every unit with dimensions and reinforcement, the joints with sealant or gasket shape and size, the anchorage to the building frame with the loads it must carry, the reglets and inserts, each surface finish with its transitions, and the integral colors. Then check that one finish paragraph governs each exposed surface, that the samples, full-size panel, and mockup are kept or deleted on purpose, that the joint widths and envelope tie-ins are drawn because the section gives none, and that the design responsibility for connections is clear.

Assemble the review package

Gather the exterior elevations with the precast panel layout and finish legend, the wall sections and plan details at panel joints, corners, openings, parapets, and the base, the structural framing plans and slab and spandrel edge details with embeds or support steel at each floor and the roof, the structural general notes with design loads and the delegated design list, the joint sealant schedule, the air barrier, insulation, and flashing details, the site plan for a sample and mockup location, any site furnishing or paving plans with precast bollards, benches, or pavers, and the issued Section 03 45 00 with Sections 07 92 00, 03 30 00, the structural steel section, and the flashing and air barrier sections. Follow one panel from its elevation mark to its finish, joints, connections, and supporting member before assuming the others match.

WBDG publishes UFGS 03 45 00: Precast Architectural Concrete as a public guide-specification reference (accessed November 16, 2026). Use your project’s issued specification and amendments for the actual comparison; the guide specification does not automatically govern your project. The checklist below is an original suggested review workflow, not a reproduction of the UFGS requirements.

Eight checks to run against the issued set

Use one record per location or system. The CSV contains the same eight prompts plus fields for source revisions, observed evidence, the review owner, the decision, and closure references.

Eight specification-to-drawing checksSwipe or scroll sideways to read all columns.
CheckSources to compareQuestion to resolve
What the drawings must showDrawing note (a complete design; location and details of units with all dimensions and reinforcement; joint details with sealant or gasket shape, dimensions, and location; anchorage devices to the building frame and connections of other materials, with gravity, live, and dynamic loads; reglet and insert locations; location of each surface finish with details of transitions; integral colors) + wood nailer, reglet, anchorage device, and gasket notes (locations and cross sections must be indicated) + elevations, wall sections, and detailsDo the elevations key every panel and unit with a mark, finish, and color, do the details show each joint type with its sealant or gasket shape and size, do the connection details show anchorage types and the loads the manufacturer needs, and are reglets, nailers, and inserts located on the drawings rather than left to the shop drawings?
Design responsibility, loads, and connectionsStandards and Loads (ASCE 7-16, ACI 318, PCI MNL-122; design loads on the drawings; differential temperature bracket whose default Fahrenheit value does not match its default Celsius value or the note) + Connections (type and configuration indicated; Contractor designs and sizes all connections) + Design Calculations (members, connections, and embedments not shown; sealed by a registered engineer; lifting) + Thermal Calculations (ASHRAE 90.1; connector spacing and solid concrete area) + structural general notes and delegated design listDo the structural notes give the wind, seismic, and gravity loads the panels and connections must carry, is the delegated connection design listed with what the engineer of record will review, has the specifier entered the temperature differential in one consistent unit pair, and does the load standard edition match the one the project’s governing criteria adopt?
Finishes, colors, and transitionsSmooth, Exposed-to-View Surfaces (all exposed surfaces unless otherwise indicated) + Exposed Aggregate Finish (all exposed surfaces, including chamfers and returns, unless otherwise indicated) + Finishing for Formed Surfaces brackets (exposed aggregate by sanding and acid wash, abrasive blast, acid etch, honed, polished) and note + Exposed-to-View Facing Mixture bracket (white, gray, or buff cement) + Exposed Aggregate and fine aggregate paragraphs + Coloring Admixture bracket + finish legend and elevationsHas the specifier kept one default finish and named every other finish by location, so the smooth and exposed aggregate paragraphs do not both claim all exposed surfaces, does each finish on the elevations match a kept bracket and its method, are transitions between finishes detailed at reveals, and do the drawings or the section name the aggregate and integral color the finish depends on?
Samples, full-size panel, and mockupConcrete Wall Panel Surface Finish Sample (small finish sample, then one full-size sample wall panel, unbracketed) + SD-04 (Full Size Sample Wall Panel bracketed; Form Liner; Brick Color Chips; Mock-up) + Mock-Up (anchors, connections, flashing, and joint fillers; water repellent applied and water-tested; job mock-up panel with edge, reveal, and brick coursing as shown; transported to the site and erected where directed) + Pre-Installation Meeting (water repellent applicator bracket) + sample display note + site planHas the specifier decided whether a full-size sample panel is required and made the submittal list agree, is a water repellent specified somewhere if the mockup is to be treated and water-tested, since this section specifies none, does the mockup include the joint, flashing, and connection actually detailed on the drawings, and does the site plan or the section say where the mockup stands?
Panel joints, gaskets, sealants, and the envelopeJoints (widths as specified unless otherwise indicated; the section specifies none) + Joint Sealing (Section 07 92 00) + Joint Materials (premolded closed-cell chloroprene gasket to the cross section indicated; brittleness temperature printed in metric and inch-pound values that do not agree) + Joints and Gaskets (continuous, compressed) + Flashing Reglets (stainless unbracketed, copper and galvanized brackets; note against galvanized at sea coasts and for staining) + Insulated Panel Accessories + wall sections, joint details, sealant schedule, and air barrier detailsAre joint widths dimensioned on the details, is each joint drawn as a sealant joint, a gasket, or both, with the gasket cross section shown, do the sealant schedule and Section 07 92 00 cover the precast joints, does the air barrier and insulation line run continuously across panel joints and openings, and has one reglet metal been kept that suits the exposure?
Embedded items, anchorage, and connections to the framePlates, Angles, Anchors and Embedment + Inserts (threaded, wedge, and slotted; galvanizing brackets; the threaded insert paragraph allows cast steel and then requires malleable iron) + Wood Nailer Inserts (location and size must be indicated; AWPA use category) + Built-In Anchorage Devices note + Connection Devices (clip angles, clamps, fasteners) + Building Framing System (supporting members and embeds provided before placement) + Erection (welding to AWS D1.1, zinc-rich touch-up, grout as shown) + Welded Connection Visual Inspection + structural framing plans and edge detailsDo the framing plans and spandrel or slab edge details show the embeds, angles, or support steel each panel bears and ties to at every floor and the roof, is it clear which trade furnishes and sets embeds in the steel or cast-in-place frame, do the connection details allow for the erection tolerances, and has the specifier fixed the threaded insert material sentence?
Plant and erector categories, thin brick, and other unitsFabricator Quality Certifications (PCI Group A category bracket AT, AD, AC, AB, or AA, or APA or NPCA) and category note + Erector Certification (PCI category A or S2) and Erector Qualifications bracket + opening note (wall panels, mullions, bollards, urns, railings, sills, copings, benches, planters, pavers) + Thin Brick Veneer (properties, face size bracket, color chips, form liner and bond breaker samples) + Sand-Cement Mortar and Pointing Grout notes + Precast Drawings bracket (brick joints and coursing aligned across panel joints) + elevations and site plansDoes the PCI category chosen match the most demanding units drawn, such as multiple mixes, returns, or tight tolerances, rather than only site furnishings, is the erector category right for load-bearing or non-load-bearing units, and where thin brick is drawn, do the elevations set the brick size and show coursing that aligns across panel joints, with one joint-filling method kept?
Strength, tolerances, acceptance, and the section’s own wordingQuality Control Testing During Fabrication (three specimens of each set tested at 28 days) versus the evaluation paragraph (averages two) + Concrete Strength at Time of Precast Unit Installation (two paragraphs printed, note says delete one) + Tolerances (PCI MNL-117 unless otherwise specified by “the Architect”) versus Modification of References (Architect/Engineer means the Contracting Officer) + defect limits that differ among Repair of Surface Defects, Finishing for Formed Surfaces, and Rejection + bearing pads citing AASHTO LRFD and MIL-C-882E (not in References) + fly ash note (no Class C) versus the blended cement bracket (Class C pozzolan)Has the specifier made the strength evaluation match the testing table, kept one installation-strength paragraph, said who may set tighter tolerances, and set one defect limit for exposed surfaces that matches the approved sample, and do the elevations or notes call out any tighter tolerances or viewing distances the design relies on?

Worked example: two panel finishes, thin brick, and connections nobody drew

Illustrative example: a three-story administration building is clad in architectural precast panels with an acid-etched field, smooth bands at each floor line, thin brick at the base, and precast copings and sills. The issued Section 03 45 00 keeps both the smooth and the exposed aggregate paragraphs with “unless otherwise indicated”, keeps the acid-etched and abrasive-blast brackets, requires a full-size sample panel while the submittal list brackets it, and keeps the water repellent steps in the mockup. The elevations hatch the two finishes without a transition detail, the joint details show a two-stage sealant joint with no dimension, and the steel framing plans show no embeds or support angles at the spandrel beams.

Ask the architect to add a finish legend that names the acid-etched and smooth finishes by location, to detail the transition reveal, to dimension the panel joints, and to show the air barrier tie-in at each joint. Ask the specifier to keep one default finish paragraph, to delete the unused finish brackets, to make the full-size sample and the submittal list agree, and to specify or delete the water repellent. Ask the structural engineer to give the panel design loads and to show the support steel and embeds at the spandrels, and to confirm which connections the precast engineer designs.

Avoid a false conflict

Section 03 45 00 covers plant-cast architectural units. Precast structural framing follows Section 03 45 33 or 03 41 33 and their guides, cast-in-place architectural concrete follows Section 03 33 00 and its guide, tilt-up panels follow their own section, joint sealants follow Section 07 92 00, flashing, air barriers, and insulation follow their own sections and guides, and the support frame follows the structural steel or concrete sections, so check those before calling a requirement missing. Some of the section’s own wording needs resolving: the temperature differential brackets do not convert, the strength evaluation and testing table count different specimens, the full-size sample and the submittal list disagree, the mockup treats with a water repellent the section never specifies, two finish paragraphs each claim all exposed surfaces, three paragraphs set different defect limits, the gasket brittleness values do not agree, joint widths are “as specified” with none specified, both installation-strength paragraphs print, the threaded insert material is stated two ways, and the bearing pad paragraph cites documents not in References. Ask the specifier which wording the project intends before treating a difference as a design conflict.

When requirements disagree, follow the project’s document-control and clarification process. Do not assume that drawings always override specifications, or the reverse. Identify the exact sources and request an authorized decision.

Close the issue across the affected documents

Record the location or tag, drawing and specification references, issue dates, observed difference, and the decision needed. Assign an owner and keep the item open until the response identifies the governing requirement. Check the revised drawings and specification references together; a response email alone may leave the issued package inconsistent.

For the overall process, use the guide to drawing and specification conflicts. Mark an inapplicable checklist row with a reason, and distinguish a verified correction from a question that still needs design information.

Where Groundbook fits

Groundbook’s drawing and specification review helps investigate potential disagreements in the documents you supply. Include the relevant specification sections and drawing references, then verify the cited evidence with the responsible reviewers before acting on a finding.

Questions, answered

FAQs

What should a precast architectural concrete review compare?

Compare what the drawings must show, design responsibility, loads, and connections, finishes, colors, and transitions, samples, the full-size panel, and the mockup, panel joints, gaskets, sealants, and the envelope, embedded items and connections to the frame, plant and erector categories and thin brick, and strength, tolerances, and acceptance.

What must the drawings show under UFGS 03 45 00?

The drawing note of the current UFGS 03 45 00 Precast Architectural Concrete on WBDG asks for a complete design with the location, dimensions, and reinforcement of each unit, joint details with sealant or gasket shape and size, anchorage to the building frame with the loads to be carried, reglet and insert locations, the location of each surface finish with transition details, and the integral colors. UFGS numbers are DoD guide specification numbers, not universal MasterFormat titles, and your project’s issued specification governs.

How is this different from the precast structural and architectural concrete guides?

The precast structural concrete and pretensioned precast guides follow UFGS 03 45 33 and 03 41 33, which cover plant-made framing members such as beams, columns, double tees, and hollow-core slabs. The architectural concrete guide follows UFGS 03 33 00 for exposed concrete cast in place. UFGS 03 45 00 covers plant-cast units chosen for their appearance, with finish samples, a full-size panel, a mockup, gaskets, thin brick, and acceptance by appearance, so check which section each unit on the drawings points to.

Can Groundbook check precast cladding drawings against Section 03 45 00?

Groundbook compares the drawing set with the specification sections and reference documents you upload, such as your issued Section 03 45 00, Sections 07 92 00 and 03 30 00, the structural general notes, the air barrier and flashing details, and licensed standards you hold, and returns potential conflicts with links to the source pages. It has no built-in code library and does not design panels or connections, calculate loads or thermal values, certify compliance, or approve submittals or samples. Each finding is a question for the architect, the structural engineer, the precast engineer, the specifier, or the contracting officer.

Keep exploring

Continue your review

Check precast structural concrete specifications against framing drawings

Compare precast framing layout, delegated member design, topping, bearing and connections, openings, fire rating, and PCI certification with UFGS 03 45 33.

Explore

Check pretensioned precast concrete specifications against framing plans, strand data, camber, and hollow-core details

Compare strand and tendon data, detensioning, camber, plant testing, bearing pads, hollow-core openings, and roof slab joints with UFGS 03 41 33.

Explore

Check architectural concrete specifications against elevations, form joint layouts, finish legends, and sample panels

Compare exposed concrete finishes, form liners and ties, sample panels, galvanized reinforcing, cleaning, and sealer extent with UFGS 03 33 00.

Explore

Check tilt-up concrete specifications against panel elevations and details

Compare tilt-up panel layout, sealed fabrication drawings, lifting and bracing inserts, connections, finishes, and casting slab with UFGS 03 47 13.

Explore

Check joint sealant specifications against drawings

Compare joint sealant type, joint design, substrate compatibility, and movement capability across wall details and specifications. Editable CSV included.

Explore

Check flashing and sheet metal specifications against roof and wall details

Compare sheet metal choices, gutters and downspouts, copings, counterflashing and reglets, expansion joints, and roof edge wind uplift with UFGS 07 60 00.

Explore

Check air barrier specifications against drawings

Compare air barrier continuity, transitions, penetrations, and testing requirements across wall sections and specifications. Editable checklist included.

Explore

Check insulation specifications against wall sections

Review insulation type, thickness, thermal-value basis, continuity, and adjacent materials across wall sections and specifications. Editable CSV included.

Explore

Check masonry specifications against wall details

Compare masonry unit types, reinforcement, grout, flashing, joints, and support details with the issued specification. Includes an editable checklist.

Explore

Make the delegated design criteria and interfaces explicit

Understand delegated design, its criteria and review handoffs. Trace a designed package into the receiving drawings with an editable checklist.

Explore

Curtain wall and facade review checklist

Review facade system boundaries, anchorage, movement, barrier continuity, glazing, and perimeter fire joints. 12 prompts and a free editable CSV.

Explore

Drawings vs. specifications

Compare drawing requirements with specifications, schedules, and controls. Find potential equipment, material, and scope inconsistencies with Groundbook AI.

Explore

Bring your next set into focus

Set up a review or talk through your project with our team.

Check your precast cladding spec against the elevations and details

Trusted by hundreds of professionals